Why Is There No Water in My Toilet Tank? 

Did you just try to flush your toilet, and nothing changed? Look inside the tank, and you could see no water inside. Before you stress, relax knowing that correcting this issue is usually simple. If you can’t complete this yourself, you can always arrange toilet repair with an Expert plumber. Follow these recommendations to diagnose and repair the problem of no water in the toilet tank. 

Check the Water Supply 

The first action is to ensure that the water is turned on. If you or someone in your household recently completed a toilet repair, you probably turned off the water first. Did you forget to turn it back on? To see, turn the water shut-off valve on the wall in back of the toilet. If the valve was turned off, water will now start refilling the tank. If this does not work, test the water at your sink or another plumbing fixture. If nothing flows from the tap, you could possibly have a larger water supply issue. Contact your water company to find out more. 

Reposition or Replace the Float Mechanism 

Older toilet models use a float ball to determine the water level as it goes up in the tank. When the ball hits a specified height, the float arm it’s connected to stops the water flow. However, insufficient water might enter the tank if the ball is positioned wrong or the arm is broken. To adjust the float ball, start by removing the toilet tank cover. Bend the float arm up just a little bit to adjust where it sits in the tank. If this fails to fix the problem, you might need to replace the whole float mechanism. You should be able to complete this yourself by following the directions that come with the replacement parts, or you can work with a plumber for help. Just understand that float balls are old toilet design. You may prefer improved reliability and efficiency if you upgrade the existing tank components or replace the toilet altogether. 

Adjust the Fill Valve 

Newer toilets use a float cup rather than a float ball, coupled with a fill valve and water level rod. There could quite possibly be no water in the toilet tank because the valve has slipped out of place or become blocked. Here are recommendations to try: 

• Adjust the fill valve: Look inside the toilet and locate the fill valve on top of a vertical tube device on the left side of the tank. Make sure it’s secure and evenly connected to the tube. Then, fine-tune the water level. Newer toilets have an adjustment knob you can turn manually, while older models may require you to loosen an adjustment screw with a flathead screwdriver. Flush the toilet and let the tank refill to check the water level. Modify it until the water comes to {about|approximately|roughly]] one inch below the top of the overflow tube. 
• Clean the fill valve: Mineral buildup and other gunk may be blocking the valve and preventing your toilet from filling. Shut off the water behind the toilet and remove the fill cap. Then, slowly turn the water back on, cupping your hand over the valve to prevent water from spraying everywhere. After several seconds, turn the water back off. Finally, clean off the fill cap to clear away hard water buildup. If the cap is cracked, replace it. 
• Clean the valve tube: The tube below the fill valve could also be plugged. Shut off the water and remove the valve hardware. Then, stick a slim bottle brush or wire down the tube. Turn the water back on just a little to flush away the junk. Replace the valve hardware and flush the toilet to test your work. 

Repair or Replace the Trip Assembly

If you’ve attempted the steps above without any luck, the last possibility is a broken trip assembly. This component connects the flush handle to the tank. If it’s damaged or positioned poorly, the flush cycle may not complete, leaving the tank empty. Remove the toilet tank lid and examine the trip assembly attached to the handle. If it’s out of place, reposition it. If the assembly is twisted, worn or busted, change it out. Whether you perform the job yourself or leave it to a plumber, this simple repair should get your toilet tank filled with water once again. 

Schedule Toilet Repair Today 

You can’t go long without a functional toilet, so reach out to [Company name] to request a toilet repair. We can determine why your toilet isn’t filling and propose the appropriate fix. If your plumbing fixture is old and worn out, our team can install a high-efficiency toilet in your home. Be assured that every plumbing repair and replacement we perform is backed by a 100% satisfaction guarantee. To schedule an evaluation from one of our licensed team members, please reach out to your community Service Experts Heating, Air Conditioning & Plumbing office today.